<< Click to Display Table of Contents >> Navigation:  Alarm Panels > Visonic > PowerMax

For complete instructions click the above link for pdf manual. Click thumbnail for expanded keypad view.

Arming/Disarming

Away Arming

1.Ensure 'READY' is displayed on the system.

2.Press the AWAY button. The red ARMED light will be lit when armed to Away mode.

Home (Stay) Arming

1.Ensure 'READY' is displayed on the system.

2.Press the HOME button. The red ARMED light will flash when armed to Home mode.

Disarming/Stopping Alarms

1.Press the OFF button.

2.Enter your Code.

Bypassing

1.From a disarmed state, press the NEXT button until the display reads, 'USER SETTINGS'.

2.Press the SHOW/OK button.

3.Enter the Master Code. The system will display, 'SET BYPASS'.

4.Press the SHOW/OK button. The first zone name and status will be displayed.

5.To bypass this zone, press the SHOW/OK button. The system will display, '<OK> TO BYPASS'.

6.Press the SHOW/OK button. The system will display, 'Z01: BYPASSED'.

7.If you wish to check the state of the next zone, press the NEXT button.

8.Press the HOME button. The system will display, 'SET BYPASS'.

9.Press the AWAY button when done to exit programming.

Alarm Memory

•When the memory contains at least one event, and the system is in a disarmed state, a flashing MEMORY message will be displayed.

•To review memory content, click the SHOW/OK button.

•In response to additional clicking of the SHOW/OK button, the display shows details of other events in memory (if any), or reverts to it's initial state.

•The memory indication and content are cleared when the system is next armed.

Chime Mode

To turn the Chime on or off, press the 8 button.

Setting The Time

1.From a disarmed state, press the NEXT button until the display reads, 'USER SETTINGS'.

2.Press the SHOW/OK button.

3.Enter the Master Code. The system will display, 'SET BYPASS'.

4.Press the NEXT button until the system displays, 'SET TIME & FORMAT'.

5.Press the SHOW/OK button.

6.Press the SHOW/OK button again.

7.Enter 4 digits for the time (HH:MM), then press * to select AM, or # to select PM.

8.Press the SHOW/OK button.

Setting the Date

1.From a disarmed state, press the NEXT button until the display reads, 'USER SETTINGS'.

2.Press the SHOW/OK button.

3.Enter the Master Code. The system will display, 'SET BYPASS'.

4.Press the NEXT button until the system displays, 'SET DATE & FORMAT'.

5.Press the SHOW/OK button.

6.Press the SHOW/OK button again.

7.Enter the date in MM/DD/YYYY format.

8.Press the SHOW/OK button.

9.Press the SHOW/OK button again.

Trouble Conditions

•If a trouble condition is present, TRBL will flash in the display, the TROUBLE indicator illuminates, and the keypad will beep three times every minute.

•To silence the trouble beeps disarm the system again (even though the system is already disarmed). This will stop the beeping for four hours.

•You can review the specific troubles, one by one, by clicking the SHOW/OK button. When all the troubles have been shown, the display will revert to the initial trouble display.

Programming User Codes

1.From a disarmed state, press the NEXT button until the display reads, 'USER SETTINGS'.

2.Press the SHOW/OK button.

3.Enter the Master Code. The system will display, 'SET BYPASS'.

4.Press the NEXT button until the system displays, 'SET USER CODES'.

5.Press the SHOW/OK button. The system will display 'User Code 1'.

6.Press the SHOW/OK button.

7.Enter the new 4 digit Code.

8.Press the SHOW/OK button.

9.Press the NEXT button to proceed to User code 2.

10.Continue the same way up to Code 8.

11.Press the SHOW/OK button.

12.Press the HOME button. 'SET USER CODES' is displayed.

13.Press the AWAY button to quit programming.