<< Click to Display Table of Contents >> Navigation:  Alarm Panels > GE > Simon/Simon 3

For complete instructions, click the above links for the pdf manuals. Click Thumbnails for expanded keypad views.

ARMING/DISARMING

ARMING doors and windows

1.Close all protected doors and windows.

2.Press Arm Doors & Windows button.

3.Enter Access Code, if needed.

ARMING motion sensors

1.Press Arm Motion Sensors button once.

2.Enter Access Code, if needed.

DISARMING

Enter the Access Code using Code buttons.

BYPASSING

indirect Bypassing

Used to automatically bypass open sensors when arming.

1.Close all doors and windows, except the ones you wish to remain open.

2.Press Arm Doors & Windows button.

3.Enter Access Code, if needed.

Any sensors that are opened will be bypassed automatically after exit.

Direct bypassing

Used to turn off specific sensors while the system is armed.

1.Press the Bypass button until you reach the sensor you want to bypass (sensor must currently be unbypassed)

2.Enter the Master Code.

Direct Unbypassing

Used to reactivate (Unbypass) sensors while the system is armed.

1.Press the Bypass button until you reach the sensor you want to unbypass (sensor must currently be bypassed)

2.Enter the Master Code, or change arming level.

DOOR CHIME

To turn door chime on or off, press the Chime Doors button. When on, the panel will announce 'Chime On', when off the panel will announce 'Chime Off'.

Setting the clock

If the panel loses power, the clock must be set. The default setting is 12 hour mode. Your installer may have set the clock to 24 hour mode.

1.Open the panel cover. Panel announces, 'Use numbered keys to enter ID'.

2.Enter the Master Access Code. Panel announces, 'Please select from Start Menu'.

3.Press Clock Set from the Start Menu. Panel announces, 'Time is ****, to change press Hours and Minutes, then press Done'.

4.Follow the arrow from the Clock Set button to the Hours keys.

5.Press the Hours +/– keys and listen to the voice prompts. Stop when panel voice announces the correct hour.

6.Press the Minutes +/– keys and listen to the voice prompts. Stop when the panel announces the correct minutes.

7.Press Done. The panel will announce the set time.

8.Close the cover.

Trouble beeps

When your security system detects a trouble condition, six rapid beeps sound every minute, until the trouble condition is corrected.

Silencing trouble beeps

To stop the trouble beeps, press the SYSTEM STATUS button or arm/disarm the system while the trouble condition exists. Trouble beeps will begin 4 hours later, unless the trouble condition is corrected.

Clearing system status

Press the SYSTEM STATUS button, listen to the status message, then disarm the system to clear system status. If the trouble condition was a low system battery, perform a sensor test. The SYSTEM STATUS button should turn off if all trouble conditions have been corrected.

PROGRAMMING user CODES

How to change an access code

1.Open the cover of the panel.

2.The panel voice prompts you to 'Use numbered keys to enter ID'. Enter your Master Access Code using the numbered keys.

3.The panel voice prompts you to 'Please select from START MENU'. Press the Add button on the START MENU.

4.The panel voice prompts you to 'Select from MAIN MENU'. Press the Access Code button on the MAIN MENU.

5.The panel voice responds with 'Master Code, press again for next access code, DONE to select or press CANCEL to quit'. Press the Access Code button again to hear the next access code. When you hear the access code you wish to change press the DONE Button.

6.Enter 3-6 new numbers using the numbered keys. (Access Code length is programmed

7.by the installer.)

8.Close the panel cover.

How to Delete an Access Code

1.Open the cover of the panel.

2.The panel voice prompts you to 'Use numbered keys to enter ID'. Enter your Master Access Code using the numbered keys.

3.The panel voice prompts you to 'Please select from START MENU'. Press the Delete button on the START MENU.

4.The panel voice prompts you to 'Select from MAIN MENU'. Press the Access Code button on the MAIN MENU.

5.The panel voice responds with 'Access Code 1, press again for next access code, DONE to select or press CANCEL to quit'. Press the Access Code button again to hear the next access code. When you hear the access code you wish to delete, press the DONE Button. The panel voice responds with 'Access Code X deleted'.

6.Close the panel cover.