<< Click to Display Table of Contents >> Navigation:  Alarm Panels > GE > Simon XT

For complete instructions, click the above link for the pdf manual. Click Thumbnail for expanded keypad view.

ARMING/DISARMING

ARMING doors and windows

1.Close all protected doors and windows.

2.Press Doors & Windows button.

3.Enter Access Code, if needed.

ARMING motion sensors

1.Press Motions button.

2.Enter Access Code, if needed.

Arming doors, windows and motion sensors

1.Close all protected doors and windows.

2.Press Doors & Windows button.

3.Enter Access Code, if needed.

4.While the panel is in the process of arming, press Motions button.

DISARMING

1.Press the Disarm button

2.Enter the Access Code when the display shows 'Enter Code'.

BYPASSING

Bypassing

1.Press Bypass button and enter the Master Code.

2.Scroll until you reach the sensor to be bypassed. The display shows, for example, 'SN 1 Front Door', on the first line.

3.Press OK to bypass (deactivate) the sensor. When a sensor is bypassed the display shows 'Bypassed' on the second line.

Unbypassing

1.Press Bypass button and enter the Master Code.

2.Scroll until you reach the sensor to be unbypassed. (The sensor must currently be bypased).

3.Press OK to unbypass (reactivate) the sensor. The panel removes the word 'Bypassed' from the second line.

DOOR CHIME

To turn door chime on or off :

1.Scroll until the display shows Chime and then press OK. The current setting will flash.

2.Scroll to toggle the chime feature on or off, and then press OK. The setting will stop flashing.

3.Press Status to exit.

A solid bell icon will appear in the display when the chime feature is enabled.

Setting the Time & Date

To reset the clock

1.Scroll until the display shows 'Set Clock', and then press OK. The display shows 'Enter Code'.

2.Enter your Master Code with the numeric keys, and then press OK.

3.Press OK again. The display flashes the hours.

4.Scroll to set the hours, and then press OK. The display flashes the minutes.

5.Scroll to set the minutes, and then press OK. The display flashes am/pm.

6.Scroll to set the am/pm, and then press OK. The display shows the current time and stops flashing.

7.Press Status twice to exit.

To set the date

1.Scroll until the display shows 'Set Date', and then press OK. The display shows 'Enter Code'.

2.Enter your Code with the numeric keys, and then press OK. The display shows the date.

3.Press OK. The display flashes the year.

4.Scroll to set the year, and then press OK to accept the setting. The display flashes the month.

5.Scroll to set the month, and then press OK to accept the setting. The display flashes the day.

6.Scroll to set the day, and then press OK to accept the setting. The display shows the programmed date.

7.Press Status twice to exit.

System status

Press Status (no code is required) to cause the system to display and speak the following types of information:

•Alarm conditions

•Alarm history

•Trouble conditions

•Open sensors

•Bypassed sensors

The Status button blinks when an active alarm exists. The Status button is lit when an abnormal condition such as a trouble or open sensor exists in the system.

You can clear certain status entries from the system (such as an alarm history) by pressing Disarm after checking the status.

PROGRAMMING user CODES

How to change the master code

1.Press one of the Scroll buttons or the OK button to enter the system menu.

2.Scroll until the display shows 'System Programming', and then press OK. The display shows 'Enter Code'.

3.Enter your Master Code, and then press OK.

4.Scroll until the display shows 'Access Codes', and then press OK.

5.Scroll until the display shows 'Master Code', and then press OK. The current value of the code flashes.

6.Enter a new code (use the correct length), and then press OK.

7.Press Status repeatedly to exit.

How to change a user code

1.Press one of the Scroll buttons or the OK button to enter the system menu.

2.Scroll until the display shows 'System Programming', and then press OK. The display shows 'Enter Code'.

3.Enter your Master Code, and then press OK.

4.Scroll until the display shows 'Access Codes', and then press OK.

5.Scroll until the display shows the user code you want to change, and then press OK. The current value of the code flashes.

6.Enter a new code (use the correct length), and then press OK.

7.Press Status repeatedly to exit.

How to delete user code

1.Press one of the Scroll buttons or the OK button to enter the system menu.

2.Scroll until the display shows 'System Programming', and then press OK. The display shows 'Enter Code'.

3.Enter your Master Code, and then press OK.

4.Scroll until the display shows 'Access Codes', and then press OK.

5.Scroll until the display shows the user code you want to delete, and then press OK. The current value of the code flashes.

6.Press Disarm, and then press OK.

7.Press Status repeatedly to exit.